When to Call an Electrician for Commercial and Industrial Properties

Maintenance of the electrical works of any commercial or industrial building is more complicated than the upkeep of residential electrical work. Any responsible building manager also knows that it’s crucial to perform these inspections to ensure the safety of the people.

Here are several electrical problems that most commercial and industrial buildings experience.

1. Dimming or Flickering Lights. If your in-house staff has just recently replaced the light bulbs but the lighting is still poor because of the constant flickering and dimming, then the connection if probably poor. This can be a problem in older building in Singapore that have not been inspected by a licensed electrician for a long time. Adding fixtures without inspecting if the electrical works can meet the needs will create this problem. Call an electrician services in Singapore to have the electrical connections inspected and the faulty fixtures replaced properly.

2. Grounding. This refers to idea of reducing contact with electrical hazards, especially in offices that house a lot of people and equipment. In simpler terms it is the method creating a way for electricity to return to the ground through the service panel in case a short circuit happens. Proper grounding is essential if you want your devices to work properly, because they generate a lot of electrical noise.

3. Loss of or Excess Power. Dips and sags in power are not obvious at first until they damage equipment. This is usually caused by faulty connections and the use of poor or worn-out materials. If your office is within an old building, it might be a good idea to hire a certified electric technician in Singapore to inspect the connections and determine whether it needs to be upgraded or replaced.

4. Overloading. This can be considered a type of safety standard violation in any building. It also puts you at risk of fires if the insulation of the wirings melts and damage the connection. Small sparks eventually lead to electrical fire. Call a good electrician in Singapore whenever your company plans to install new equipment such as computers to determine if you are overloading or not.

5. Electrical Failure. Commercial grade and industrial equipment need more power than residential appliances, that is why it is crucial that you consult a good electrician in Singapore to determine if the circuit can supply enough power to newly-installed machines. Electrical failure can cause fires and accidents, that is why you should not wait for the equipment to malfunction before you call an electrician.

6. Sparks and Hot Switches and Fixtures. The first sign of electrical failure are the hot switches and electrical fixtures. Don’t wait for the plugs or switches to spark before you call electrician services to determine the problem. Sparks not only damage your commercial or industrial equipment but can also cause fire or damage parts of your electrical works.

7. Electrical Surges. Poor wiring, especially in older buildings in Singapore can cause damaged lines and faulty equipment. The people he in building will not often notice power surges because they last only for a few seconds. If overlooked, frequent power surges can damage a lot of equipment and will cost you more money than a scheduled electrical inspection. Call an electrician to inspect the wiring and the devices that are plugged to determine if the electrical works are adequate for your needs.

8. Over-circuited Panel. Call an electrician when an over-circuited panel is causing problems. An over-circuited panel means that there are two breakers in one slot instead of one.

9. High Electric Bills. If there are changes in your electrical bill, the first you need to check are the electronic devices that might be using more power. But if you don’t have new equipment recently installed, then there could be some damage in the wiring or circuits. Call an electrician to root out the problem.

10. Tripping Breakers. If your electrical circuits are overloaded, then you will most likely experience tripping breakers. Short circuits and ground fault can also cause this and may even lead to fire. When this happens, instruct the staff to shut off the electrical source and call a licensed electrician as soon as possible.

11. Incorrect Installation and Use. Commercial and industrial buildings should follow the standards of proper installation and use of electricity. If you need to renovate or expand the office, it is crucial to consult an electrician services firm in Singapore like http://www.powermax.com.sg/ for professional installation of electrical works. If you need to have new equipment or machine installed, call a licensed electrician to determine if your electrical supply is enough. You cannot just plug in new equipment without knowing if it’s going to be a fire hazard or not. Regular inspection will also prevent most of the problems listed above, as well as ensuring that safety guidelines are followed by the staff. Responsible use of electricity means that you have a basic understanding of how electricity and appliances function.

12. Electric Shocks. This is common in old buildings that have not been inspected for some time. Circuits that have been fitted more than 15 years ago need to be checked by an electrician to avoid accidents whenever a device is plugged in.

13. Few Outlets. Moving into an old commercial building can be a hassle if you have a lot of equipment and there are few outlets. In some offices, the cheapest solution is to buy power strips and extension cords. They work but they are also a fire hazard. If you have a shortage of outlets for your equipment, call a licensed electrician for a proper assessment.

14. Poor Layout. In some old buildings, wires are exposed and are potentially a fire hazard in areas that have heavy traffic of people. Ideally, wires should be hidden behind walls or ceilings and should not trip passers-by. Call an electrician to inspect the wirings and fix minor problems that might cause a fire.